Thermoplastic road marking paint consists of C5 petroleum resin, EVA, PE wax, filler materials, which is solid powder state at normal temperatures. It will liquify if heated by pre-heater to 180-200ºC. Coating the paint onto the road, a hard film will form. With reflective glass beads sprinkled onto the surface, it has good reflective effect in the dark, making it widely applied to roads and highways. Paint can be customized according to your local environmental conditions, such as temperature and humidity.
TECHNICAL SPECIFICATION
| Product name |
Thermoplastic Paint for Road Marking |
| Ingredient |
C5 petroleum resin, titanium dioxide, PE wax and so on |
| Color |
White/yellow/red/blue/green/customized |
| Packing |
25kg/bag |
| Density(g/cm3) |
1.8-2.3 |
| Softening point(ºC) |
90-125 |
| Compressive strength(MPa) |
≥12 |
| Liquidity |
35±10 |
| Glass bead content |
0 / 20% / 25% / 30% |
Application description
Hot melt reflective marking paint is mainly used for more than 2 level of the highway and highway, the marking coating thickness of this paint is (1.0 ~ 2.5) mm, the paint is mixed with reflective glass beads, and in the marking construction, the surface of the reflective glass beads. This marking has good night reflective performance, long service life, according to the traffic flow of large highway construction of all kinds of road marking paint demand estimates, small and the quality of the paint itself, generally up to (2 ~ 3) years. The construction of hot melt coating requires special heating equipment. For the second recoating of the old marking line, the thicker old coating should be removed before coating.
Construction mode
Hot melt marking paint is solid powder at room temperature. During construction, the paint is put into the melting kettle, and the temperature in the kettle is controlled between 180 ° C and 210 ° C. While melting, it is stirred, and after melting, it is put into the insulation melting hopper of the marking car. Melt coating then back into the marking bucket, and heat preservation to keep the material molten state. Before the line is marked by the pre-marking machine position, according to the design drawing indicated on the coating position with the lower coating machine primer. The marking coating can be applied only after the coating agent dries thoroughly. When the scribing begins, the scribing bucket should be placed on the road, because there is a certain gap between the scribing bucket and the ground, when the scribing car ahead, by automatic flow and scrape out a neat line. The glass bead spreader can automatically and evenly spread a layer of reflective glass beads on the marking line.
1.Strong Adhension Power and Durability
2.High Dirty Pick-up Resistance
3.Save Cost of Gas and High Usage Ratio
4.Not Fade Easily
5.Dry Fast Features:
|
|
Mark on the Road with effects of guidance and Warn
|
|
|
Normal Thermoplastic
|
|
|
C5 Petropols, EVA, PE wax, titanium dioxide, filler materials
|
|
|
Powder
|
|
|
White & Yellow (OEM)
|
|
|
25kg/bag
|
|
|
180-200°C
|
Touch/ Full Dry Time After Marking
|
3/10 mins
|
|
|
12 months
|
|
|
1.Strong Adhension Power and Durability
2.High Dirty Pick-up Resistance
3.Save Cost of Gas and High Usage Ratio
4.Not Fade Easily
|
Advantage
Hot-melt road marking coating uses the thermoplasticity of synthetic resin to make the hot-melt coating have quick-drying
property, and the hot-melt property of synthetic resin is used to make the marking and pavement firmly bonded. Hot melt reflective road marking coatings are generally composed of thermoplastic resins, fillers, reflective materials and other additives. Hot melt coatings are powdery at room temperature. There is no solvent volatile component in the composition. It is melted by construction heating, then coated on the ground with specialized equipment and solidified into a film by physical cold condensation. For hot melt road coating, its fluidity is a very important technical index in the construction process.
To better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient packaging services will be provided.
Q1: How can l get a quotation?
A1: Please send us your inquiry, our sales team will communicate with you and quote you as soon as possible.
Q2: Can I get a sample before place order?
A2: Yes, we could provide the sample of paint for free and it will be prepared within 3 days.
Q3: Do you provide customized service?
A3: Yes, we have professional technical team. If you have special requirements, such as color of paint, glass bead content, please let us know.
Q4: What is your leading time ?
A4: Generally , the leading time is within 7 days, also depending on your quantity.
Q5: What is your terms of payment?
A5: Payment terms vary depending on countries. Generally, payment≤10,000 USD, 100% T/T in advance; payment>10,000 USD, 30% T/T in advance, balance before shipment.
Audited Supplier 
){kind=link}
){kind=link}